Description

Product overview

Empire DVCT40CBP95 is a 40-inch single-sided clean-face direct-vent gas fireplace with TruFlame dual-burner technology. Choose the exact factory natural-gas or propane model and model-matched interior components.

Key features

Ceramic glass and a traditional log-fire presentation. The multifunction control operates variable flame height, independent rear-burner switching and accent-light dimming as described in the model’s owner instructions.

Included components

Fine-mesh protective barrier, noncombustible board and multifunction remote control. Install the required protective components before operation.

Required components

DVCT40CBP95 requires a compatible liner and log set purchased and installed before operation. Use the matching 40-inch log and liner families listed for this model. Optional decorative fronts, frames and insets do not replace those required internal components. A decorative inset requires its compatible front assembly.

Optional accessories

Decorative frames, fronts, andirons and compatible insets are optional. An inset requires its matching front; it does not replace required logs or liner.

FBB21 automatic variable-speed twin blower is optional. Its compatible remote control function does not mean a blower is included.

Specifications

ModelDVCT40CBP95
LocationIndoor
ConfigurationSingle-sided
IgnitionIntermittent pilot
Appliance width × height × depth49 × 42-3/4 × 24 inches; height excludes standoffs
Maximum input, both burners; natural gas / propane47,500 / 45,000 BTU/h
Minimum input, both burners; natural gas / propane30,000 / 35,000 BTU/h
Minimum input, front burner only; natural gas / propane15,000 / 16,500 BTU/h
Gas inlet1/2-inch NPT
Venting5 × 8 direct vent, top outlet

Installation and safety notes

The appliance uses an approved 5 × 8 direct-vent system to draw combustion air from outside and discharge exhaust outdoors. Vent route, termination, framing, clearances and any conversion-kit selection must follow the exact model manual. The dimensions above describe the appliance and are not rough-opening dimensions.

Manuals and downloads

Manufacturer installation manual for DVCT40CBP95, page 8, provides these fuel-specific input ratings, dimensions and component requirements. Installation and service must follow the complete manufacturer documentation and applicable codes.

Specifications

SKU: DVCT40CBP95
Condition: New

Empire Hearth

Empire Hearth 40" Rushmore Clean-Face Zero-Clearance Direct Vent Fireplace DVCT40CBP95

Write a Review
Expert Help Available (844) 545-7995
SKU: DVCT40CBP95
Condition: New
$6,555.00
BUY WITH CONFIDENCE Fireplace expertise from selection to delivery.
✓
Shipping & Delivery Most in-stock items are released for shipment within 1–2 business days after payment and order review. Carrier transit is additional.
✓
Free Shipping Eligible orders: free standard shipping to the contiguous U.S. Exclusions apply.
✓
Best Price Guarantee Eligible identical products from authorized U.S. retailers; compare total delivered price before tax. Request before purchase or within 7 calendar days after purchase.
✓
Contractor Pricing Trade professionals can contact us for project and volume pricing.
✓
30-Day Returns Request a return within 30 days for eligible new, unused, uninstalled items. Authorization and exclusions apply.
✓
Fireplace Experts Need help choosing? Talk to an expert before you order.
CONFIGURE YOUR FIREPLACE

Build Your Fireplace

Complete the required selections first, then add only the compatible options your fireplace and installation need.

1 Required selections
2 Customize options
3 Review & order
Expert Help (844) 545-7995

Fireplace

Complete the required product selections for this fireplace.

Required
  • Empire Hearth 40" Birch 10 piece Direct Vent Burncrete Log Set LS40CBB
  • Empire Hearth 40" Ceramic Fiber Driftwood Log Set LS40DINF
  • Empire Hearth 40" Ceramic Fiber Traditional Charred Log Set LS40TINF
  • Empire Hearth 40" Whitewashed Herringbone Brick Ceramic Fiber Liner DVP40CPWH
  • Empire Hearth 40" Rustic Brick Liner DVP40PMB
  • Empire Hearth 40" Old World Stone Liner DVP40PWS
  • Empire Hearth 40" Black Porcelain Liner with Matte Black Ceiling Floor DVP40PKR
  • Empire Hearth 36" Forged Black Iron Frame DFF36BL
  • Empire Hearth 36" Arched Black Forged Iron Inset DFF36RBL
  • Empire Hearth 36" Black Rectangle Forged Iron Inset DFF36CBL
  • Empire Hearth 36" Distressed Pewter Forged Iron Frame DFF36FPD
  • Empire Hearth 36" Distressed Pewter Arched Forged Iron Inset DFF36RPD
  • Empire Hearth 36" Distressed Pewter Forged Rectangle Iron Inset DFF36CPD
  • Empire Hearth 36" Oil-Rubbed Bronze Forged Iron Frame DFF36BZT
  • Empire Hearth 36" Oil-Rubbed Bronze Arched Forged Iron Inset DFF36RBZT
  • Empire Hearth 36" Oil-Rubbed Bronze Rectangle Forged Iron Inset DFF36FBZT
  • Empire Hearth 40" Textured Black Beveled 1.5" Frame DF402BLX
  • Empire Hearth 40" Oil-Rubbed Bronze1.5" Beveled Frame DF402BZT
  • Empire Hearth 40" Brushed Nickel 1.5" Beveled Frame DF402NB
  • Empire Hearth Gravity 36" Heat Management Includes 36" Plenum and 10' Flex Vent HMGW36
  • Empire Hearth External Forced Air Heat Management, Requires Flex Kit HMFA
  • Empire Hearth Flex Vent for Forced Air Kit with 25' Flex Vent and Clamps SD6DFA25
  • Empire Hearth Auto Variable Speed Twin Blower FBB21
  • Empire Hearth Natural Gas to Propane Conversion Kit - MF 36884
  • Empire Hearth Propane to Natural Gas Conversion Kit - MF 36885
  • Duravent 5"/8" Double Wall Galvalume 6" Vent Pipe 58DVA-06
  • Duravent 5"/8" Double Wall Galvanized 9" Vent Pipe 58DVA-09
  • Duravent 5"/8" Double Wall Galvanized 12" Vent Pipe 58DVA-12
  • Duravent 5"/8" Double Wall 18" Galvalume Vent Pipe 58DVA-18
  • Duravent 5"/8" Double Wall 24" Galvalume Vent Pipe 58DVA-24
  • Duravent 5"/8" Double Wall 36" Galvalume Vent Pipe 58DVA-36
  • Duravent 5"/8" Double Wall 48" Galvalume Vent Pipe 58DVA-48
  • Duravent 5"/8" Double Wall 60" Galvalume Vent Pipe 58DVA-60
  • Duravent 5"/8" Double Wall 8 1/2" Pipe Extension Galvalume Vent Pipe (3" - 7") 58DVA-08A
  • Duravent 5"/8" Double Wall 16" Pipe Extension Galvalume Vent Pipe (3" - 14-1/2") 58DVA-16A
  • Duravent 5"/8" Double Wall 11" - 14-5/8" Pipe Extension Galvalume Vent Pipe (9-1/2" - 15-1/2") 58DVA-17TA
  • Duravent 5"/8" Double Wall 17" - 24" Pipe Extension Galvalume Vent Pipe (15-1/2" - 22-1/2") 58DVA-24TA
  • Duravent 5"/8" Double Wall 36" Concentric Flex Galvalume Vent 58DVA-36FF
  • Duravent 5"/8" Double Wall 60" Concentric Flex Galvalume Vent 58DVA-60FF
  • Duravent 5"/8" Double Wall 120" Concentric Flex Galvalume Vent 58DVA-120FF
  • Duravent 5"/8"Double Wall Galvalume 30 Degree Elbow 58DVA-E30
  • Duravent 5"/8"Double Wall Galvalume 45 Degree Elbow 58DVA-E45
  • Duravent 5"/8"Double Wall Galvalume 60 Degree Elbow 58DVA-E60
  • Duravent 5"/8"Double Wall Galvalume 90 Degree Elbow 58DVA-E90
  • Duravent 5"/8"Double Wall Galvalume Elbow Strap 58DVA-ES
  • Duravent 5"/8" Wall/Ceiling Thimble Cover 58DVA-DC
  • Duravent 5/8" Wall Thimble 58DVA-WT
  • Duravent 5/8" Wall Thimble – Reduced (use w/ round horizontal & sconce cap only) 58DVA-WTS
  • Duravent 5/8" Wall Thimble – Universal 58DVA-WTU
  • Duravent 5/8" Wall Firestop 58DVA-WFS
  • Duravent 5/8" Wall Strap 58DVA-WS
  • Duravent 5/8" Roof Support 58DVA-RS
  • Duravent 5/8" Cathedral Ceiling Support Box 58DVA-CS
  • Duravent 5/8" Ceiling Firestop 58DVA-FS
  • Duravent 5/8" Attic Insulation Shield 58DVA-IS
  • Duravent 5/8" Vinyl Siding Standoff (Sized for 58DVA-HC) 58DVA-VSS
  • Duravent 5/8" Vinyl Siding Standoff Kit (4-pc. sized for 58DVA-HC) 58DVA-VSK
  • Duravent 4" - 6-5/8" Vinyl Siding Standoff Kit V46DVA-VSKS
  • DuraVent Vent Reducer 5”x8” to 4”x6 5/8” 58DVA-X46
  • Duravent 5/8" Storm Collar 58DVA-SC
  • Duravent 5/8" Flashing - 0/12-6/12 Pitch 58DVA-F6
  • Duravent 5/8" Flashing - 7/12-12/12 Pitch 58DVA-F12
  • Duravent 5/8" Flashing - Flat 58DVA-FF
  • Duravent 5/8" Dead Soft Flashing - 0/12-6/12 Pitch for Metal Roofs 58DVA-F6DS
  • Duravent 5/8" Dead Soft Flashing - 7/12-12/12 Pitch for Metal Roofs 58DVA-F12DS
  • DuraVent Rubber Boot Flashing Kit - Max 12/12 Pitch, for Metal Roofs 200275
  • Duravent DuraTech 6" Diameter Snow Splitter 6"-10" 6DT-SP
  • Duravent 5/8" Square High Wind (Alum) 58DVA-HC
  • Duravent 5/8" Sconce High Wind (Alum) 58DVA-HSCH
  • Duravent 5/8" Snorkel Termination Cap 14” 58DVA-SNK14
  • Duravent 5/8" Snorkel Termination Cap 36” 58DVA-SNK36
  • Duravent 5/8" Round Cap w/ Square Base 58DVA-HRCS
  • Duravent 4" - 6-5/8" Horizontal Windguard 46DVA-WG
  • Duravent 5/8" High Wind Termination Cap 58DVA-VCH
  • Duravent 5/8" Low Profile Termination Cap 58DVA-VC
  • Duravent 4" - 6-5/8" Vertical Windguard 46DVA-VWG
Hurry up! Current stock:
Available to order
READY TO ORDER

Your Fireplace Configuration

Review your selections, then add your configured fireplace to cart.

Configuration Calculator
Fireplace —
Selected Components $0.00
Selected Accessories $0.00
Configured Total —
Need help before ordering? Talk to a Product Expert (844) 545-7995
  • product-security-image-1.jpg
  • product-security-image-2.jpg
  • product-security-image-3.jpg
  • product-security-image-4.jpg
30-Day Returns Eligible items; authorization and exclusions apply

Request a return within 30 calendar days after delivery for eligible new, unused, unassembled and uninstalled items in original packaging. Written authorization is required. Read the Returns Policy for conditions, fees and exclusions.

Return Window 30 Days
Return Support Email Our Team
Shipping & Delivery Clear delivery expectations and tracking

Most in-stock items are released for shipment within 1–2 business days after payment and order review. Carrier transit is additional. Parcel transit commonly takes 3–7 business days; freight commonly takes 5–10 business days after shipment. Special-order and backordered items may take longer. Shipping details, exclusions and damage reporting.

Most In-Stock Items: Processing 1–2 Business Days After Review
Standard Shipping Eligible Contiguous U.S. Orders

Product overview

Empire DVCT40CBP95 is a 40-inch single-sided clean-face direct-vent gas fireplace with TruFlame dual-burner technology. Choose the exact factory natural-gas or propane model and model-matched interior components.

Key features

Ceramic glass and a traditional log-fire presentation. The multifunction control operates variable flame height, independent rear-burner switching and accent-light dimming as described in the model’s owner instructions.

Included components

Fine-mesh protective barrier, noncombustible board and multifunction remote control. Install the required protective components before operation.

Required components

DVCT40CBP95 requires a compatible liner and log set purchased and installed before operation. Use the matching 40-inch log and liner families listed for this model. Optional decorative fronts, frames and insets do not replace those required internal components. A decorative inset requires its compatible front assembly.

Optional accessories

Decorative frames, fronts, andirons and compatible insets are optional. An inset requires its matching front; it does not replace required logs or liner.

FBB21 automatic variable-speed twin blower is optional. Its compatible remote control function does not mean a blower is included.

Specifications

ModelDVCT40CBP95
LocationIndoor
ConfigurationSingle-sided
IgnitionIntermittent pilot
Appliance width × height × depth49 × 42-3/4 × 24 inches; height excludes standoffs
Maximum input, both burners; natural gas / propane47,500 / 45,000 BTU/h
Minimum input, both burners; natural gas / propane30,000 / 35,000 BTU/h
Minimum input, front burner only; natural gas / propane15,000 / 16,500 BTU/h
Gas inlet1/2-inch NPT
Venting5 × 8 direct vent, top outlet

Installation and safety notes

The appliance uses an approved 5 × 8 direct-vent system to draw combustion air from outside and discharge exhaust outdoors. Vent route, termination, framing, clearances and any conversion-kit selection must follow the exact model manual. The dimensions above describe the appliance and are not rough-opening dimensions.

Manuals and downloads

Manufacturer installation manual for DVCT40CBP95, page 8, provides these fuel-specific input ratings, dimensions and component requirements. Installation and service must follow the complete manufacturer documentation and applicable codes.

Customers Also Viewed