True North TN40 Pellet Insert — 33040001
SKU / Model: 33040001
Fireplace only$4,931.85
Unlock an exclusive offer on this product.
Product overview
The True North TN40 Pellet Insert turns an existing wood-burning fireplace into a clean, easy-to-run pellet heater. It is built from heavy-gauge steel with a wide firepot for a full flame, and it burns so cleanly that its certified emissions are just 0.69 g/hr.
The hopper holds up to 60 pounds of pellets behind an easy-opening lid with a safety shut-off switch. Digital controls offer manual, automatic and hi/low operation with five heat levels, and with a wall thermostat the insert runs itself to your set temperature. An automatic igniter, air-wash glass and a self-cleaning stainless steel burn pot liner keep day-to-day care simple, and two convection blowers carry the heat into the room.
The insert ships with a 42" × 29" surround, and an oversize surround is available for larger fireplace openings.
Key features
- Up to 36,000 BTU. Wide firepot and two convection blowers.
- Very low emissions. 0.69 g/hr, EPA 2020 certified; 79.6% LHV efficiency.
- Up to 60 lb hopper. Easy-open lid with safety shut-off switch.
- Three operating modes. Manual, automatic and hi/low (automatic and hi/low use a wall thermostat).
- 5-level heat control. Easy-access digital controls.
- Automatic igniter.
- Self-cleaning burn pot. Stainless steel burn pot liner.
- Clean glass. Air-wash technology over 104 sq. in. of glass.
- Surround included. 42" × 29" × 1 1/2" standard surround.
- Mobile home approved.
Included components
The TN40 Pellet Insert (33040001) comes complete with its cast iron door, hopper, standard 42" × 29" surround, two convection blowers, stainless steel burn pot liner and the installation and operating manual.
Required components
Venting is not included. The insert has a 3" flue collar and needs a 3" or 4" stainless steel liner listed to UL 1777 (an increaser is required for 4"); in the USA a direct flue connection is allowed, while Canada requires a full liner to the top of the chimney. Maximum vent length is 45 feet, and 4" vent is recommended above 4,000 feet. The fireplace must be a masonry or approved factory-built wood-burning fireplace with an opening of at least 29 1/2" wide at the front, 24" wide at the rear, 16" deep and 21 1/4" high, and a non-combustible hearth extending 16" in front of the opening. A 120-volt grounded outlet is required (a surge-protected power bar is recommended).
Optional accessories
The oversize 48" surround backing plate (33120001) covers larger fireplace openings, and a low-voltage or millivolt wall thermostat (not included) enables automatic and hi/low modes. The oversize surround and approved DuraVent pellet liner kits can be selected below.
Specifications
| Model / MPN | TN40 Insert Series A — 33040001 (TN40INSA) |
|---|---|
| Brand | True North (Pacific Energy Fireplace Products) |
| Appliance type | Pellet fireplace insert |
| Fuel | Premium wood pellets only |
| Maximum heat output | 36,000 BTU/hr (per True North) |
| EPA tested output | 6,000 – 25,600 BTU/hr |
| Heat input | Approximately 10,000 – 38,000 BTU/hr, depending on fuel |
| Efficiency | 79.6% LHV / 73% HHV |
| Emissions | 0.69 g/hr — EPA 2020 certified |
| Hopper capacity | Up to 60 lb |
| Glass viewing area | 104 sq. in. |
| Unit weight | 300 lb (manual) |
| Minimum fireplace opening | 29 1/2" W front, 24" W rear, 16" D, 21 1/4" H |
| Surround | Standard 42" W × 29" H × 1 1/2" (included); oversize 48" W backing plate 33120001 (optional) |
| Flue / venting | 3" collar; 3" or 4" UL 1777 stainless liner; maximum vent length 45 ft; no flue damper |
| Clearances to combustibles | Adjacent side wall 12", side facing 8 1/2", top facing / mantel 13", front 36", ceiling 54" from the base of the unit |
| Hearth | Non-combustible, 16" in front of the fireplace opening and 6" beyond each side of the viewing door |
| Electrical | 120 V, 60 Hz; 2.5 A normal, 4.3 A peak |
| Outside air | Accepts 2" ID non-combustible pipe |
| Safety listing | ASTM E1509-12, ULC S628 (Intertek); for use in mobile homes |
Installation and safety notes
Install the TN40 only in a masonry or approved factory-built wood-burning fireplace with at least the minimum opening listed above, and keep the manual's clearances to side walls, side facings and mantels. The hearth in front must be non-combustible and reach 16 inches beyond the fireplace opening. Remove or permanently open any flue damper; none is permitted with the insert.
Vent through a listed 3" or 4" stainless steel liner within 45 feet of total length. Outside air can be brought in through 2" pipe via an ash clean-out, a hole through the back of the fireplace or flex pipe up the chimney, with the intake well below the flue termination.
Burn only premium wood pellets and plug the insert into a grounded 120-volt outlet, ideally through a surge-protected power bar.
Safety warnings and disclaimer
WARNING: Using this product can expose you to chemicals including carbon monoxide, which is known to the State of California to cause birth defects or other reproductive harm, and soot, which is known to the State of California to cause cancer. For more information, visit www.p65warnings.ca.gov.
INSTALLATION SAFETY: For your safety, follow the manufacturer's installation and operating instructions exactly. An incorrect installation can lead to a fire, property damage or personal injury. United Fireplaces recommends that every appliance be installed by a qualified professional installer.
DISCLAIMER: Flames and flame colors on the website may appear differently in real life.
Warranty summary
True North pellet products carry a limited warranty to the original purchaser for normal residential use: 3 years parts and 1 year labor on the firebox, castings and glass (glass for thermal breakage only), 1 year parts and labor on electrical components and switches, and 1 year parts only on gaskets, paint (peeling), bricks, firebox liner and burn pot and liner. Installation must be by a qualified technician to the instructions and codes, and the warranty is not transferable.
Manufacturer manuals and downloads
- TN40 Pellet Insert installation and operating manual (100004050, rev. 201123)
- TN40 Pellet Insert brochure
- TN40 EPA test data
- True North pellet products warranty
- Register your True North product
Frequently asked questions — TN40 Pellet Insert
Will the TN40 insert fit my fireplace?
The opening must be at least 29 1/2" wide at the front, 24" wide at the rear, 16" deep and 21 1/4" high, in a masonry or approved factory-built wood-burning fireplace.
Does it need a chimney liner?
In the USA a direct flue connection is allowed, though a full 3" or 4" stainless liner is the common choice; in Canada a full liner to the top of the chimney is required.
What if my fireplace opening is larger than the surround?
Add the oversize surround backing plate (33120001).
Do I need a thermostat?
No. Manual mode works without one; automatic and hi/low modes need an optional wall thermostat.
Loading component details…
