Remii 60" Wall Mount Lumina Electric Fireplace WM-60-LUMINA

Product overview

The Remii WM Lumina is a 60-inch linear electric fireplace that hangs on the wall, recesses into a built-in, or sits semi-flush in a standard 2×4 wall with the optional trim. Hidden venting sends the heat out the top and keeps the face clean, so nothing distracts from the fire.

The Lumina update brings a more lifelike flame, new lighting and tray lights you can adjust to suit the moment. The flames come in three colors, and the fireplace runs 4 dB quieter than before, so evenings stay calm.

Run it from the remote or from your phone over WiFi, with the heat on or off. It works in living rooms, bedrooms and offices, and in covered outdoor spaces protected from direct rain, so the same fire can warm a patio or porch.

Key features

• Three ways to install. Hang it on the wall, build it in, or fit it semi-flush in a 2×4 wall with the optional trim.
• Improved Lumina flame. A more realistic, lifelike flame effect.
• Three flame colors. Change the flame color to suit the room.
• New lights with tray light control. Adjust the tray lighting for the glow you want.
• 4 dB quieter. Quieter operation than the previous WM model.
• WiFi control. Run the fireplace from your phone.
• Remote control included. Flames, lights and heat from across the room.
• Flames without heat. Run the flame effect on its own all year.
• Two heat levels. 1,200 watts high or 600 watts low.
• Hidden venting. Heat exits at the top for a clean face with no visible grill.
• Plug-in or hardwire. Plugs into a grounded 120-volt outlet, or a qualified electrician can hardwire it.
• Indoor or covered outdoor. Approved for outdoor areas protected from direct water, with the required overhang.
• 2-year limited warranty. Backed by Remii.

Included components

The fireplace ships with its front glass and trim, a 12-piece oak log set, wall hanger, safety screw, wall plugs and the remote control.

Required components

For a wall mount, a solid wall that can take at least 8 wall anchors (8 mm holes, 40 mm deep). For a built-in, a framed opening of 60 3/4" W × 16" H × 6" D. For a semi-flush install in a 2×4 wall, a 4" deep opening and the semi-flush trim, sold separately. A 15-amp, 120-volt, 60 Hz branch circuit with proper ground, preferably dedicated, or a hardwire connection by a qualified electrician.

Optional accessories

Semi-flush mount surround (black, 2 1/4" deep), required for a semi-flush install. Dark Grey and Bronze surrounds for the WM series. Remii also offers 15 colors of optional fire glass: Clear Reflective, Ocean Blue, Charcoal, Champagne, Dark Grey, Clear Gem, White, Dusty Purple, Amber, Orange, Suntea, Black, Sable, Smokey Grey and White, and Canyon Brown.

Specifications

Installation and safety notes

Choose a dry spot at least 3 feet (0.9 m) from curtains, furniture, bedding and other combustibles. In a bathroom, the fireplace must be on a GFI-protected circuit with an accessible outlet and kept well away from tubs and showers, since it is not watertight.

For a wall mount, level the hanger, check the wall for wiring and pipes, drill at least 8 holes, fit the wall plugs, fasten the hanger and secure the fireplace with the safety screw. For a built-in, frame a 60 3/4" W × 16" H × 6" D opening with at least 1/4" around the unit, remove the trim, glass and inner side panels, fix the fireplace with two screws per side and refit everything after adding media. A semi-flush install uses a 4" deep opening and the special trim. Any wall thermostat must be wired before the fireplace goes in, and hardwiring must be done by a qualified electrician.

Outdoors, install it only where it is protected from direct water. The overhang must extend to the front and each side by at least half the roof-line height, measured from the base of the fireplace, so an 8-ft roof line needs a 4-ft overhang. Remii's warranty requires the stainless-steel cover and/or suitable shelter for outdoor or high-moisture installs, and proof of purchase for it.

Safety warnings and disclaimer

WARNING: This product can expose you to chemicals including lead in the wiring, which is known to the State of California to cause birth defects or other reproductive harm. For more information, visit www.p65warnings.ca.gov.

INSTALLATION SAFETY: For your safety, follow the manufacturer's installation and operating instructions exactly. An incorrect installation can lead to a fire, property damage or personal injury. United Fireplaces recommends that every appliance be installed by a qualified professional installer.

DISCLAIMER: Flames and flame colors on the website may appear differently in real life.

Warranty summary

Remii covers this fireplace with a 2-year limited warranty from the date of first purchase, for the original purchaser, against manufacturing and material defects. Replacement parts and shipping are free, but labor is not covered, LED lights are excluded and proof of purchase is required.

Manufacturer manuals and downloads

• Installation and operation manual, WM series (Ver.1, May 2021)
• WM-60 technical specification sheet
• Outdoor installation instructions
• Remii brochure (2024)
• Remii brochure (2022)
• Remii limited warranty
• Remii product presentation (PowerPoint)

Frequently asked questions — WM-60-LUMINA

Can the WM-60-LUMINA be hung on the wall or built in?

Both. It hangs on the wall with the included hanger, builds into a 60 3/4" W × 16" H × 6" D opening, or fits semi-flush in a 2×4 wall with the optional trim.

Does it need to be hardwired?

No. It plugs into a grounded 120-volt outlet on a 15-amp circuit, preferably dedicated. A qualified electrician can hardwire it if you prefer.

Can I use the flames without heat?

Yes. The flames and lights run on their own, so you can enjoy them all year.

Can the WM-60-LUMINA be installed outdoors?

Yes, in an outdoor area protected from direct water, with an overhang to the front and each side of at least half the roof-line height.