American Fyre Designs Contractor's w/Moulding Vented 045
SKU / Model: 045-11-A-WC-RBC
Fireplace only$5,254.00
Unlock an exclusive offer on this product.
Product overview
The American Fyre Designs Contractor's Model with Moulding is a full-size outdoor fireplace shell supplied in White Concrete with a recessed hearth and body, ready for your own stone, tile or stucco. Cast chimney-top and body mouldings give it a more finished, traditional silhouette than the standard Contractor's Model. This listing is the vented version (series 045), built with the vented chimney and four-piece firebox liner set.
The fireplace is the shell only: the R.H. Peterson gas burner and log set are sold separately and are required to operate it.
Key features
- 67" W x 37" D x 91" H
- Chimney-top and body moulding included
- Unfinished White Concrete shell with recessed hearth and body for field-applied veneer
- 11-piece kit; combustible flooring permitted beneath the unit
- Certified to ANSI Z21.97/CSA 2.41 when installed with select R.H. Peterson vented gas appliances
- Outdoor use only
Specifications
| Model series | 045 (vented) |
|---|---|
| Overall dimensions | 67" W x 37" D x 91" H |
| Manufacturer weight | 1,230 lb, 11 pieces |
| Finish | White Concrete (WC), unfinished, recessed hearth and body (code A) |
| Compatible burners | R.H. Peterson G52 (match-lit or valve up to 18/20"), G45 (log set or glass; match-lit up to 24", valve up to 18/20") or G22 (match-lit up to 24", valve up to 18") vented burners |
| Fuel | Natural gas or propane (propane requires a valve and pilot burner; propane may not be match-lit) |
| Gas inlet pressure | Natural gas 5" to 10.5" w.c.; propane 11" to 13" w.c. |
| Gas supply line | 1/2" minimum inside diameter; runs over 20 ft may need a larger line |
| Clearances to combustibles | Sides 6", rear 6", front 36", below 0"; no construction permitted above the unit |
| Overhead | Vented models may not be installed under any overhead construction |
| Gas configuration | RBC (key valve on the right side) |
| Certification | ANSI Z21.97/CSA 2.41 outdoor decorative gas appliances (with select R.H.P. gas appliances) |
What's included
Hearth, shelf, body, mantel, vented chimney, chimney-top and body moulding, firebox liners with shims, and interior, exterior, moulding and chimney-top hardware kits.
Required (sold separately)
An R.H. Peterson vented gas appliance (burner with matching log set or media), the gas shut-off valve, hose and regulator, and your finish veneer. Propane installations need a ventilated cylinder enclosure (R.H.P. venting panel 5510-01 is referenced for custom enclosures) or an American Fyre Designs tank/end table.
Downloads
- Contractor's Model outdoor fireplace installation manual (L-H2-023)
- Ventilation and clearances important notice (L-H2-001)
- American Fyre Designs product catalog
- Official Contractor's Model with Moulding product page
Installation and safety notes
Set the fireplace on a hard, level surface. This is an unfinished product intended to be finished with tile, stonework or a similar substrate. Above 2,000 ft elevation, input ratings are reduced about 4% per 1,000 ft. Install and connect gas to local codes, or in their absence ANSI Z223.1/NFPA 54 (CSA B149.1/B149.2 in Canada). Not for use inside any building, garage or enclosed space.
WARNING: This product can expose you to chemicals including carbon monoxide, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov.
DISCLAIMER: Flames and flame colors on the website may appear differently in real life.
INSTALLATION SAFETY: Follow the manufacturer's installation and operating instructions exactly. Improper installation can cause fire, property damage or injury. United Fireplaces recommends that every appliance be installed by a qualified professional installer.
Loading component details…

