American Fyre Designs Contractor's Vent-Free Fireplace 140
SKU / Model: 140-11-A-WC-RBC
Fireplace only$5,254.00
Unlock an exclusive offer on this product.
Overview
The American Fyre Designs Contractor's Model is a blank slate: a full-size outdoor fireplace shell supplied in White Concrete with a recessed hearth and body, ready for you to finish in your own stone, tile, stucco or other veneer. Grand Series styling gives it a tall, architectural chimney and mantel. This listing is the vent-free Contractor's Model (series 140), built with the unvented chimney and five-piece firebox liner set (extra top liner), which allows overhead construction 3 feet or more above the unit.
The fireplace is the shell only: the R.H. Peterson vent-free gas burner and log set are sold separately and are required to operate it.
It needs 6" of clearance at the sides and rear and 36" in front of the hearth, and overhead construction must be at least 3 ft above the top of the unit. It sits on a hard, level surface, and combustible flooring is permitted beneath it. Natural gas or propane burners can be used; propane burners need a valve and pilot and cannot be match-lit. American Fyre Designs covers the fireplace for three years.
Key features
- 67" W x 37" D x 96" H
- Unfinished White Concrete shell with recessed hearth and body for field-applied veneer
- Hearth, shelf, body, mantel and chimney supplied as a 9-piece kit
- Combustible flooring permitted beneath the unit
- Certified to ANSI Z21.97/CSA 2.41 when installed with select R.H. Peterson unvented gas appliances
- 1,220 lb in 9 pieces
- Takes R.H. Peterson G10 stainless steel vent-free burner (up to 24/30" with a 24" log set), G21 stainless steel vent-free burner (up to 24") or ODG15 stainless steel burner (up to 24/30" with a 24" log set)
- Clearances: 6" sides and rear, 36" front, 0" below; above: 36" (no overhead construction less than 3 ft above the top of the unit)
- Outdoor use only
- 3-year limited warranty on the fireplace
Specifications
| Model | American Fyre Designs Contractor's Model, vent-free (140 series) |
|---|---|
| Type | Outdoor gas fireplace, vent-free, unfinished sectional concrete shell for field-applied veneer; burner and log set sold separately; outdoor use only |
| Unit dimensions | 67" W x 37" D x 96" H; 1,220 lb, 9 pieces |
| Framing dimensions | None required (freestanding outdoor fireplace set on a hard, level surface) |
| Viewing area | Not published by the manufacturer |
| Clearances to combustibles | Sides: 6" (hearth edge to combustible construction). Rear: 6". Front: 36" (hearth extension to combustible construction). Below: 0" (hard, level surface; combustible materials permitted). Above: 36" (no overhead construction less than 3 ft above the top of the unit). Propane cylinder enclosure: 6" sides, 0" above |
| Finish | White Concrete (WC), unfinished, recessed hearth and body (code A) |
| Compatible burners | R.H. Peterson G10 (up to 24/30" with 24" log set), G21 (up to 24") or ODG15 (up to 24/30" with 24" log set) unvented stainless burners (manual L-H2-023, Table 2, p.14) |
| Fuel | Natural gas or propane (propane requires a valve and pilot burner) |
| Gas inlet pressure | Natural gas 5" to 10.5" w.c.; propane 11" to 13" w.c. |
| Gas supply line | 1/2" minimum inside diameter; runs over 20 ft may need a larger line |
| Shut-off valve | Accessible gas shut-off valve within 6 ft of the unit (not included) |
| Gas configuration | RBC (key valve on the right side) |
| Certification | ANSI Z21.97/CSA 2.41 outdoor decorative gas appliances (with select R.H.P. gas appliances) |
| Warranty | 3 years on the fireplace, GFRC products, gas logs and burners; 1 year on electrical components, valves, accessories and controls |
Included components
- Hearth
- Shelf
- Body
- Mantel
- Unvented chimney
- Firebox liner set with shims: 5 liners and 2 shims (unvented set, with the extra top liner)
- Interior hardware kits (14)
- Exterior hardware kits (10)
Required components
- R.H. Peterson G10 stainless steel vent-free burner (up to 24/30" with a 24" log set), G21 stainless steel vent-free burner (up to 24") or ODG15 stainless steel burner (up to 24/30" with a 24" log set)
- R.H. Peterson Charred Frontier Oak vent-free log set (CHFR series), or Fyre Glass / Fyre Gems with the G21 burner
- Finish veneer or substrate (tile, stonework or similar) for the recessed hearth and body
- Gas supply line, 1/2" minimum inside diameter (runs over 20 ft may need a larger line)
- Propane installations: burner with valve and pilot assembly (no match-lit propane)
- Propane installations: standard 20 lb (5-gallon) cylinder, regulator and hose of 10 ft maximum (single-stage regulator up to 95,000 BTU; two-stage up to 150,000 BTU)
- Propane installations: ventilated cylinder enclosure (at least 22" interior height and 16.5" diameter or width and depth; R.H.P. venting panels 5510-01 for custom enclosures) or an American Fyre Designs tank/end table
Downloads
- Contractor's Model outdoor fireplace installation manual (L-H2-023)
- Ventilation and clearances important notice (L-H2-001)
- American Fyre Designs product catalog
- Official Contractor's Model product page
Installation & safety notes
Set the fireplace on a hard, level surface. This is an unfinished product intended to be finished with tile, stonework or a similar substrate. Above 2,000 ft elevation, input ratings are reduced about 4% per 1,000 ft. Install and connect gas to local codes, or in their absence ANSI Z223.1/NFPA 54 (CSA B149.1/B149.2 in Canada). Not for use inside any building, garage or enclosed space.
Follow the manufacturer's installation and operating instructions exactly. Improper installation can cause fire, property damage or injury. United Fireplaces recommends that every appliance be installed by a qualified professional installer.
California Proposition 65
WARNING: This product can expose you to chemicals including carbon monoxide, which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Flames and flame colors on the website may appear differently in real life.
Frequently asked questions — American Fyre Designs Contractor's Model 140
How big is the Contractor's Model?
67" W x 37" D x 96" H. It weighs 1,220 lb and ships in 9 pieces.
What clearances does it need?
6" at the sides (from the hearth edge) and rear, 36" in front of the hearth extension and 0" below. It can go under a covered patio or pergola as long as the overhead construction is at least 3 ft above the top of the unit.
Is a burner included?
No. The fireplace is the shell only. It needs an R.H. Peterson G10 stainless steel vent-free burner (up to 24/30" with a 24" log set), G21 stainless steel vent-free burner (up to 24") or ODG15 stainless steel burner (up to 24/30" with a 24" log set), plus an R.H. Peterson Charred Frontier Oak vent-free log set (CHFR series), or Fyre Glass / Fyre Gems with the G21 burner.
Can I finish it in stone or tile?
Yes. It is supplied unfinished in White Concrete with a recessed hearth and body, and is designed to be finished with tile, stonework or a similar substrate.
Can it run on propane?
Yes. Propane installations need a burner with a valve and pilot assembly (propane may not be match-lit), a 20 lb cylinder in a ventilated enclosure and a hose of 10 ft or less. Inlet pressure: natural gas 5" to 10.5" w.c.; propane 11" to 13" w.c.
What's the warranty?
3 years on the fireplace, GFRC products, gas logs and burners, and 1 year on electrical components, valves, accessories and controls.
Loading component details…

